|
Post by SDL on Aug 19, 2019 14:42:42 GMT -8
Chet,
I just went through the whole sequence, programming OTA update AM2315, no AM2315 and it all works. I put V036 up there again.
Look in the manual and clear the EEPROM and re-initialize your unit. That might just do it.
BP
|
|
|
Post by SDL on Aug 22, 2019 6:41:59 GMT -8
Chet,
I don't know what is going on in your compiler. Can you just reboot and use the OTA Update?
BP
|
|
chet
New Member
Posts: 48
Raspberry Pi: Yes
Other Device: PC, ESP8622
|
Post by chet on Aug 26, 2019 11:38:09 GMT -8
I got it to go. I used windows and I did what you have suggested and that still did not work,
|
|
|
Post by SDL on Aug 26, 2019 11:44:53 GMT -8
What still did not work?
BP
|
|
chet
New Member
Posts: 48
Raspberry Pi: Yes
Other Device: PC, ESP8622
|
Post by chet on Aug 26, 2019 12:48:54 GMT -8
|
|
|
Post by SDL on Aug 27, 2019 14:15:07 GMT -8
But, you can set it up? Through 192.168.4.1 right?
Does OurWeatherPageAdmin work? Can you check the software version?
Can you Ping the device? Try that to make sure you have the IP address correct. It shows up on the OLED. I'm think you have not got the IP address right.
Does the weather show up on OurWeatherPage.html? I guess not rereading your comment.
Check this out a bit more and then I'll get you a new WeatherPlus board if we can't figure this out.
BP
|
|
chet
New Member
Posts: 48
Raspberry Pi: Yes
Other Device: PC, ESP8622
|
Post by chet on Aug 27, 2019 14:21:44 GMT -8
Yes i do have the correct ip and i can ping it but i cannot access the webpage.
|
|
chet
New Member
Posts: 48
Raspberry Pi: Yes
Other Device: PC, ESP8622
|
Post by chet on Aug 28, 2019 9:46:19 GMT -8
I'll try it again and I'll update of it works or not.
|
|
chet
New Member
Posts: 48
Raspberry Pi: Yes
Other Device: PC, ESP8622
|
Post by chet on Aug 28, 2019 18:41:38 GMT -8
SDL I have redone it and still the same results. Yes I can ping it. I have attached the pic of the ping results. Also, still refuse for me to connect. also yes it is the right ip as i have reserved it in the dhcp. This is getting really frustrating that it was working great until the update. So what is the solution for this issue? Chet Attachments:
|
|
|
Post by SDL on Aug 29, 2019 5:40:05 GMT -8
|
|
|
Post by robotsquirrel on Aug 29, 2019 11:17:17 GMT -8
SDL I have redone it and still the same results. Yes I can ping it. I have attached the pic of the ping results. Also, still refuse for me to connect. also yes it is the right ip as i have reserved it in the dhcp. This is getting really frustrating that it was working great until the update. So what is the solution for this issue? Chet Do you have the OLED screen attached? I was having a similar problem. What does the OLED say?
|
|
chet
New Member
Posts: 48
Raspberry Pi: Yes
Other Device: PC, ESP8622
|
Post by chet on Aug 29, 2019 13:23:36 GMT -8
robtsquirrel Yes the OLED is hooked up and it is showing the in and outdoor temp, wind and direction, rain air quality. all the usual items. It's really frustrating I can get both v35 and 36 to compile and upload. so what am I missing? SDL Same resulates with firefox.
|
|
|
Post by robotsquirrel on Aug 30, 2019 10:37:03 GMT -8
Does the OLED screen show the correct IP address on this screen?
OurWeather Connected
IP Address:
xxx.xxx.xxx.xxx <- This should be the IP you reserved and is the IP that the board should be listening on.
|
|
chet
New Member
Posts: 48
Raspberry Pi: Yes
Other Device: PC, ESP8622
|
Post by chet on Aug 30, 2019 10:39:26 GMT -8
Does the OLED screen show the correct IP address on this screen? OurWeather Connected IP Address: xxx.xxx.xxx.xxx <- This should be the IP you reserved and is the IP that the board should be listening on. Yes it does show the up. After it connects to my WIFI network. I even redid the upload and still no go.
|
|
|
Post by robotsquirrel on Aug 30, 2019 11:14:42 GMT -8
|
|