OurWeather Extender Solar WXLink LoRa - Wireless Data Link

Aaron,

It should just work.

Couple of things:

1) Do you see the light on the Transmitter blink every minute or so?

2) Have you double checked your wiring?

3) Does the OLED report that it has found the WXLink?

4) What version of OurWeather software are you running? Shows on the boot up screen.

BP

I have checked thru the wiring and everything is set correctly. Upon startup of the TX I see a solid blue light that remains on and then a yellow light flashes and stops. It doesn’t flash again.

It doesn’t appear to transmit any data as the Weatherboard 1 OLED only has zeros for the data from the charging system and now weather values on display either.

Am I missing something on the plug n play setup here?

I posted how I interpret the instructions to upload the files from the Github site.  Can you check them? Of course if you have directions on how to program the board, please email me. I downloaded all the TX files but would need to know the structure and description of the process you use.



I have an ftdi that came with the weather station.

Can you verify or provide additional guidance?

Yes I tried several times with those exact settings. I put all the files I downloaded into the libraries and opened and compiled the sketch. It gave an error that there was low memory. I connected the board and it still wouldn’t connect.

When I ran the monitor is said “init failed”

I’ll send the board back next week. We have given up trying to figure this out.

This is the TX board right? It compiled and loaded into the Mini Pro LP? Let me see exactly the whole process.

*It is the TX board - Pictures above


Did you try it with JUST the LoRa board plugged in (make sure it is in the right place!!!!) and look at the serial monitor with your FTDI cable?

*yes, it says WxLink Present init failed


IF you could show exactly what was seen on the serial monitor, it would be helpful.

*shown above


It will say init failed if the Lora Board is not plugged into the correct slot.

*Plugged into D6/D7 as shown in manual and in the photo above


We are close. I can feel it. If we can't get this to work, we will send you a new programmed board (by me even....) but I want the old one back to debug.



BP

Please tell me what I am doing wrong. I haven't done much with IDE prior to this effort. Here is the process I used...



I downloaded the zip file: SDL_Arduino_WXLink_LoRa_Tx-master.zip



I unzipped the file as show below:



insert photo 1



It created the following folder structure:



insert photo 2







I used IDE and imported the librarys from the above zip file and they show up in the bottom as Contributed Libraries.



insert photo 3





I then did the same import of a library from a zip file for the RadioHead-1.105.zip file and that shows up in the Contributed Libraries.



I then selected Verify/Compile to check the code.





This is the error I received:



Arduino: 1.6.10 (Windows 10), Board: "Arduino Pro or Pro Mini, ATmega328 (5V, 16 MHz)"



SDL_Arduino_WXLink_LoRa_Tx:86: error: 'RH_RF95' is not a template



RH_RF95<SoftwareSerial> rf95(COMSerial);



^



C:\Users\aaron\Documents\Arduino\SDL_Arduino_WXLink_LoRa_Tx-master\SDL_Arduino_WXLink_LoRa_Tx-master\SDL_Arduino_WXLink_LoRa_Tx\SDL_Arduino_WXLink_LoRa_Tx.ino: In function 'void setup()':



SDL_Arduino_WXLink_LoRa_Tx:467: error: 'RH_RF95' is not a template



rf95.setModemConfig(RH_RF95<SoftwareSerial>::ModemConfigChoice(Bw31_25Cr48Sf512));



^



SDL_Arduino_WXLink_LoRa_Tx:467: error: expected primary-expression before '(' token



rf95.setModemConfig(RH_RF95<SoftwareSerial>::ModemConfigChoice(Bw31_25Cr48Sf512));



^



C:\Users\aaron\Documents\Arduino\SDL_Arduino_WXLink_LoRa_Tx-master\SDL_Arduino_WXLink_LoRa_Tx-master\SDL_Arduino_WXLink_LoRa_Tx\SDL_Arduino_WXLink_LoRa_Tx.ino: In function 'void loop()':



SDL_Arduino_WXLink_LoRa_Tx:817: error: 'RH_RF95' is not a template



rf95.setModemConfig(RH_RF95<SoftwareSerial>::ModemConfigChoice(Bw31_25Cr48Sf512));



^



SDL_Arduino_WXLink_LoRa_Tx:817: error: expected primary-expression before '(' token



rf95.setModemConfig(RH_RF95<SoftwareSerial>::ModemConfigChoice(Bw31_25Cr48Sf512));



^



exit status 1

'RH_RF95' is not a template



This report would have more information with

"Show verbose output during compilation"

option enabled in File -> Preferences.











I then selected verbose output during compilation as shown below:



Arduino: 1.6.10 (Windows 10), Board: "Arduino Pro or Pro Mini, ATmega328 (5V, 16 MHz)"



C:\Program Files (x86)\Arduino\arduino-builder -dump-prefs -logger=machine -hardware "C:\Program Files (x86)\Arduino\hardware" -tools "C:\Program Files (x86)\Arduino\tools-builder" -tools "C:\Program Files (x86)\Arduino\hardware\tools\avr" -built-in-libraries "C:\Program Files (x86)\Arduino\libraries" -libraries "C:\Users\aaron\Documents\Arduino\libraries" -fqbn=arduino:avr:pro:cpu=16MHzatmega328 -ide-version=10610 -build-path "C:\Users\aaron\AppData\Local\Temp\build821de5cc789072119bf3aab015cbc313.tmp" -warnings=none -prefs=build.warn_data_percentage=75 -verbose "C:\Users\aaron\Documents\Arduino\SDL_Arduino_WXLink_LoRa_Tx-master\SDL_Arduino_WXLink_LoRa_Tx-master\SDL_Arduino_WXLink_LoRa_Tx\SDL_Arduino_WXLink_LoRa_Tx.ino"

C:\Program Files (x86)\Arduino\arduino-builder -compile -logger=machine -hardware "C:\Program Files (x86)\Arduino\hardware" -tools "C:\Program Files (x86)\Arduino\tools-builder" -tools "C:\Program Files (x86)\Arduino\hardware\tools\avr" -built-in-libraries "C:\Program Files (x86)\Arduino\libraries" -libraries "C:\Users\aaron\Documents\Arduino\libraries" -fqbn=arduino:avr:pro:cpu=16MHzatmega328 -ide-version=10610 -build-path "C:\Users\aaron\AppData\Local\Temp\build821de5cc789072119bf3aab015cbc313.tmp" -warnings=none -prefs=build.warn_data_percentage=75 -verbose "C:\Users\aaron\Documents\Arduino\SDL_Arduino_WXLink_LoRa_Tx-master\SDL_Arduino_WXLink_LoRa_Tx-master\SDL_Arduino_WXLink_LoRa_Tx\SDL_Arduino_WXLink_LoRa_Tx.ino"

Using board 'pro' from platform in folder: C:\Program Files (x86)\Arduino\hardware\arduino\avr

Using core 'arduino' from platform in folder: C:\Program Files (x86)\Arduino\hardware\arduino\avr

Detecting libraries used...

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "C:\Users\aaron\AppData\Local\Temp\build821de5cc789072119bf3aab015cbc313.tmp\sketch\SDL_Arduino_WXLink_LoRa_Tx.ino.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "C:\Users\aaron\AppData\Local\Temp\build821de5cc789072119bf3aab015cbc313.tmp\sketch\SDL_Arduino_WXLink_LoRa_Tx.ino.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "C:\Users\aaron\AppData\Local\Temp\build821de5cc789072119bf3aab015cbc313.tmp\sketch\SDL_Arduino_WXLink_LoRa_Tx.ino.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "C:\Users\aaron\AppData\Local\Temp\build821de5cc789072119bf3aab015cbc313.tmp\sketch\SDL_Arduino_WXLink_LoRa_Tx.ino.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "C:\Users\aaron\AppData\Local\Temp\build821de5cc789072119bf3aab015cbc313.tmp\sketch\SDL_Arduino_WXLink_LoRa_Tx.ino.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "C:\Users\aaron\AppData\Local\Temp\build821de5cc789072119bf3aab015cbc313.tmp\sketch\SDL_Arduino_WXLink_LoRa_Tx.ino.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "C:\Users\aaron\AppData\Local\Temp\build821de5cc789072119bf3aab015cbc313.tmp\sketch\SDL_Arduino_WXLink_LoRa_Tx.ino.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "C:\Users\aaron\AppData\Local\Temp\build821de5cc789072119bf3aab015cbc313.tmp\sketch\SDL_Arduino_WXLink_LoRa_Tx.ino.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "C:\Users\aaron\Documents\Arduino\libraries\jeelib\Ports.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "C:\Users\aaron\Documents\Arduino\libraries\jeelib\PortsBMP085.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "C:\Users\aaron\Documents\Arduino\libraries\jeelib\PortsLCD.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "C:\Users\aaron\Documents\Arduino\libraries\jeelib\PortsRF12.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "C:\Users\aaron\Documents\Arduino\libraries\jeelib\PortsSHT11.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "C:\Users\aaron\Documents\Arduino\libraries\jeelib\RF12.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "C:\Users\aaron\Documents\Arduino\libraries\jeelib\RF12sio.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "C:\Users\aaron\Documents\Arduino\libraries\jeelib\RF69.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "C:\Users\aaron\Documents\Arduino\libraries\jeelib\RF69_compat.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "C:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master\DS3232RTC.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "C:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master\MemoryFree.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "C:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master\SDL_Arduino_INA3221.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "C:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master\SDL_ESP8266_HR_AM2315.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src\SoftwareSerial.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "C:\Users\aaron\Documents\Arduino\libraries\RadioHead\RHCRC.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "C:\Users\aaron\Documents\Arduino\libraries\RadioHead\RHDatagram.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "C:\Users\aaron\Documents\Arduino\libraries\RadioHead\RHEncryptedDriver.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "C:\Users\aaron\Documents\Arduino\libraries\RadioHead\RHGenericDriver.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "C:\Users\aaron\Documents\Arduino\libraries\RadioHead\RHGenericSPI.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "C:\Users\aaron\Documents\Arduino\libraries\RadioHead\RHHardwareSPI.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "C:\Users\aaron\Documents\Arduino\libraries\RadioHead\RHMesh.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "C:\Users\aaron\Documents\Arduino\libraries\RadioHead\RHNRFSPIDriver.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "C:\Users\aaron\Documents\Arduino\libraries\RadioHead\RHReliableDatagram.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "C:\Users\aaron\Documents\Arduino\libraries\RadioHead\RHRouter.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "C:\Users\aaron\Documents\Arduino\libraries\RadioHead\RHSPIDriver.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "C:\Users\aaron\Documents\Arduino\libraries\RadioHead\RHSoftwareSPI.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "C:\Users\aaron\Documents\Arduino\libraries\RadioHead\RH_ABZ.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "C:\Users\aaron\Documents\Arduino\libraries\RadioHead\RH_ASK.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "C:\Users\aaron\Documents\Arduino\libraries\RadioHead\RH_CC110.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "C:\Users\aaron\Documents\Arduino\libraries\RadioHead\RH_E32.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "C:\Users\aaron\Documents\Arduino\libraries\RadioHead\RH_MRF89.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "C:\Users\aaron\Documents\Arduino\libraries\RadioHead\RH_NRF24.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "C:\Users\aaron\Documents\Arduino\libraries\RadioHead\RH_NRF51.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "C:\Users\aaron\Documents\Arduino\libraries\RadioHead\RH_NRF905.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "C:\Users\aaron\Documents\Arduino\libraries\RadioHead\RH_RF22.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "C:\Users\aaron\Documents\Arduino\libraries\RadioHead\RH_RF24.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "C:\Users\aaron\Documents\Arduino\libraries\RadioHead\RH_RF69.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "C:\Users\aaron\Documents\Arduino\libraries\RadioHead\RH_RF95.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "C:\Users\aaron\Documents\Arduino\libraries\RadioHead\RH_Serial.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "C:\Users\aaron\Documents\Arduino\libraries\RadioHead\RH_TCP.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src\SPI.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src\Wire.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "C:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src\utility\twi.c" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "C:\Users\aaron\Documents\Arduino\libraries\Time\DateStrings.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "C:\Users\aaron\Documents\Arduino\libraries\Time\Time.cpp" -o "nul"

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "C:\Users\aaron\AppData\Local\Temp\build821de5cc789072119bf3aab015cbc313.tmp\sketch\SDL_Arduino_WXLink_LoRa_Tx.ino.cpp" -o "nul"

Generating function prototypes...

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -flto -w -x c++ -E -CC -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "C:\Users\aaron\AppData\Local\Temp\build821de5cc789072119bf3aab015cbc313.tmp\sketch\SDL_Arduino_WXLink_LoRa_Tx.ino.cpp" -o "C:\Users\aaron\AppData\Local\Temp\build821de5cc789072119bf3aab015cbc313.tmp\preproc\ctags_target_for_gcc_minus_e.cpp"

"C:\Program Files (x86)\Arduino\tools-builder\ctags\5.8-arduino10/ctags" -u --language-force=c++ -f - --c++-kinds=svpf --fields=KSTtzns --line-directives "C:\Users\aaron\AppData\Local\Temp\build821de5cc789072119bf3aab015cbc313.tmp\preproc\ctags_target_for_gcc_minus_e.cpp"

Compiling sketch...

"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -flto -mmcu=atmega328p -DF_CPU=16000000L -DARDUINO=10610 -DARDUINO_AVR_PRO -DARDUINO_ARCH_AVR "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\eightanaloginputs" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire\src" "-IC:\Users\aaron\Documents\Arduino\libraries\Time" "-IC:\Users\aaron\Documents\Arduino\libraries\jeelib" "-IC:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial\src" "-IC:\Users\aaron\Documents\Arduino\libraries\RadioHead" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI\src" "C:\Users\aaron\AppData\Local\Temp\build821de5cc789072119bf3aab015cbc313.tmp\sketch\SDL_Arduino_WXLink_LoRa_Tx.ino.cpp" -o "C:\Users\aaron\AppData\Local\Temp\build821de5cc789072119bf3aab015cbc313.tmp\sketch\SDL_Arduino_WXLink_LoRa_Tx.ino.cpp.o"

SDL_Arduino_WXLink_LoRa_Tx:86: error: 'RH_RF95' is not a template



RH_RF95<SoftwareSerial> rf95(COMSerial);



^



C:\Users\aaron\Documents\Arduino\SDL_Arduino_WXLink_LoRa_Tx-master\SDL_Arduino_WXLink_LoRa_Tx-master\SDL_Arduino_WXLink_LoRa_Tx\SDL_Arduino_WXLink_LoRa_Tx.ino: In function 'void setup()':



SDL_Arduino_WXLink_LoRa_Tx:467: error: 'RH_RF95' is not a template



rf95.setModemConfig(RH_RF95<SoftwareSerial>::ModemConfigChoice(Bw31_25Cr48Sf512));



^



SDL_Arduino_WXLink_LoRa_Tx:467: error: expected primary-expression before '(' token



rf95.setModemConfig(RH_RF95<SoftwareSerial>::ModemConfigChoice(Bw31_25Cr48Sf512));



^



C:\Users\aaron\Documents\Arduino\SDL_Arduino_WXLink_LoRa_Tx-master\SDL_Arduino_WXLink_LoRa_Tx-master\SDL_Arduino_WXLink_LoRa_Tx\SDL_Arduino_WXLink_LoRa_Tx.ino: In function 'void loop()':



SDL_Arduino_WXLink_LoRa_Tx:817: error: 'RH_RF95' is not a template



rf95.setModemConfig(RH_RF95<SoftwareSerial>::ModemConfigChoice(Bw31_25Cr48Sf512));



^



SDL_Arduino_WXLink_LoRa_Tx:817: error: expected primary-expression before '(' token



rf95.setModemConfig(RH_RF95<SoftwareSerial>::ModemConfigChoice(Bw31_25Cr48Sf512));



^



Using library jeelib in folder: C:\Users\aaron\Documents\Arduino\libraries\jeelib (legacy)

Using library SDL_Arduino_WXLink_LoRa_Tx-master in folder: C:\Users\aaron\Documents\Arduino\libraries\SDL_Arduino_WXLink_LoRa_Tx-master (legacy)

Using library SoftwareSerial at version 1.0 in folder: C:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SoftwareSerial

Using library RadioHead in folder: C:\Users\aaron\Documents\Arduino\libraries\RadioHead (legacy)

Using library SPI at version 1.0 in folder: C:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\SPI

Using library Wire at version 1.0 in folder: C:\Program Files (x86)\Arduino\hardware\arduino\avr\libraries\Wire

Using library Time at version 1.5 in folder: C:\Users\aaron\Documents\Arduino\libraries\Time

exit status 1

'RH_RF95' is not a template

This was not present in the folder:


"After installing, also go down into



/home/user/Arduino/libraries/Grove_LoRa_433MHz_and_915MHz_RF-master/RadioHead.h



and replace <util/atomic.h> with <RHutil/atomic.h>
"

I went ahead and uploaded anyway.  I connected to the weather station and no data was received by the RX board.  Did you update the RX software so I should upload a new version?

TX board Results while connected to FTDI:


WXLink Tx Present

Wireless ID:3

Software Version:9

DS3231 Not Present

RTC_STATUS=11110001

RTC_CONTROL=11110001

SAP Load Voltage =-0.00



LIPO_Battery Load Voltage: -0.00 V

LIPO_Battery Current: -0.05 mA



Solar Panel Voltage: -0.00 V

Solar Panel Current: 0.05 mA



Load Voltage: -0.00 V

Load Current: -0.05 mA



SunAirPlus Not Present

wakeState=4

timeBeforeSleep=5052

Awake now: timeAfterSleep=34236

SleepTime = 29184

Millis Time: 34.24

2wakeState=2

Watchdog1 Reset - Patted the Dog

wakeState=2

MessageCount=0

AM2315 not found

Wind Vane Voltage =2.29

Wind Vane Degrees =45

TotalRainClicks=0

windClicks=1

Average Wind Speed=0.04 KPH

shortestWindTime (usec)5027528

-------

45

0

------

crc = 0xFD60

----------Sending packet----------

----------After Sending packet----------

----------Packet Sent. Sleeping Now----------

----------After Wait Sending packet----------

freeMemory()=611

bufferlength=63

AB 66 27 5C 01 00 00 2D 00 5A 7D 29 3D 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 6F 12 83 BA CC CC 4C BD CC CC 4C BD 6F 12 83 BA CC CC 4C 3D 00 00 00 00 00 00 00 00 FD 60

timeBeforeSleep=37482

Awake now: timeAfterSleep=66664

SleepTime = 29182

Millis Time: 66.66

2wakeState=2

Watchdog1 Reset - Patted the Dog

wakeState=2

MessageCount=1

AM2315 not found

Wind Vane Voltage =2.37

Wind Vane Degrees =0

TotalRainClicks=0

windClicks=0

Average Wind Speed=0.00 KPH

shortestWindTime (usec)10000000

-------

0

0

------

crc = 0x9811

----------Sending packet----------

----------After Sending packet----------

----------Packet Sent. Sleeping Now----------

----------After Wait Sending packet----------

freeMemory()=611

bufferlength=63

AB 66 27 A0 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 6F 12 83 BA CC CC 4C BD CC CC 4C BD 6F 12 83 BA CC CC 4C 3D 00 00 00 00 01 00 00 00 98 11

timeBeforeSleep=69908

Awake now: timeAfterSleep=99094

SleepTime = 29186

Millis Time: 99.09

2wakeState=2

Watchdog1 Reset - Patted the Dog

wakeState=2

MessageCount=2

AM2315 not found

Wind Vane Voltage =2.38

Wind Vane Degrees =0

TotalRainClicks=0

windClicks=0

Average Wind Speed=0.00 KPH

shortestWindTime (usec)10000000

-------

0

0

------

crc = 0x9CBB

----------Sending packet----------

----------After Sending packet----------

----------Packet Sent. Sleeping Now----------

----------After Wait Sending packet----------

freeMemory()=611

bufferlength=63

AB 66 27 E4 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 6F 12 83 BA CC CC 4C BD CC CC 4C BD 6F 12 83 BA CC CC 4C 3D 00 00 00 00 02 00 00 00 9C BB

timeBeforeSleep=102338

Awake now: timeAfterSleep=131522

SleepTime = 29184

Millis Time: 131.52

2wakeState=2

Watchdog1 Reset - Patted the Dog

wakeState=2

MessageCount=3

AM2315 not found

Wind Vane Voltage =2.39

Wind Vane Degrees =0

TotalRainClicks=0

windClicks=0

Average Wind Speed=0.00 KPH

shortestWindTime (usec)10000000

-------

0

0

------

crc = 0xEC60

----------Sending packet----------

----------After Sending packet----------

----------Packet Sent. Sleeping Now----------

----------After Wait Sending packet----------

freeMemory()=611

bufferlength=63

AB 66 27 28 05 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 6F 12 83 BA CC CC 4C BD CC CC 4C BD 6F 12 83 BA CC CC 4C 3D 00 00 00 00 03 00 00 00 EC 60

timeBeforeSleep=134767




Connected RX board to FTDI and this is what it said:

-------Receive Started---------

Software Version:4

init failed