Smart Garden Errors when running testALLSensors.py

robertr729
New Member

Posts: 4

Smart Garden Errors when running testALLSensors.py Jan 9, 2019 21:46:15 GMT -8

Quote

Post by robertr729 on Jan 9, 2019 21:46:15 GMT -8

this is the result that I am getting when I run testALLSensors.py.

pi@switchdoclabs:~/SDL_Pi_SmartGardenSystem $ sudo python testAllSensors.py
[Errno 121] Remote I/O error
[Errno 121] Remote I/O error
Error accessing 0x49: Check your I2C address
Error accessing 0x49: Check your I2C address

Test All SGS Devices Version 1.0 - SwitchDoc Labs

Program Started at:2019-01-10 00:43:33

----------------------
Main Sensors
----------------------
ADS1115: Present
OLED: Present
Sunlight Sensor: Present
hdc1000 Sensor: Present
Ultrasonic Level Sensor: Present

tested HDC1000 and it errored out.

pi@switchdoclabs:~/SDL_Pi_SmartGardenSystem/SDL_Pi_HDC1000 $ sudo python testHDC1000.py
Test SDL_Pi_HDC1000 Version 1.1 - SwitchDoc Labs

Sample uses 0x40 and SwitchDoc HDC1000 Breakout board
Program Started at:2019-01-10 12:12:28

------------
Manfacturer ID=0x5449
Device ID=0x1050
Serial Number ID=0x936E80
configure register = 0x1000
turning Heater On
configure register = 0x3000
turning Heater Off
Traceback (most recent call last):
File "testHDC1000.py", line 41, in <module>
hdc1000.turnHeaterOff()
File "/home/pi/SDL_Pi_SmartGardenSystem/SDL_Pi_HDC1000/SDL_Pi_HDC1000.py", line 147, in turnHeaterOff
HDC1000_fw.write( s2 ) #sending config register bytes
IOError: [Errno 121] Remote I/O error

----------------------
Plant / Sensor Counts
----------------------
Sensor Count: 1
Pump Count: 1

----------------------
Extender Devices
----------------------
ADS1115_Ext1: Not Present
ADS1115_Ext2: Not Present
GPIO Extender 1: Not Present
GPIO Extender 1: Not Present

----------------------
Future Smart Garden System Expansions
----------------------
SunAirPlus: Not Present
Lightning Mode: Not Present
Solar Power Mode: Not Present
MySQL Logging Mode: Not Present

done with testAll
Traceback (most recent call last):
File "testAllSensors.py", line 289, in <module>
degrees= hdc1000.readTemperature()
File "./SDL_Pi_HDC1000/SDL_Pi_HDC1000.py", line 82, in readTemperature
HDC1000_fw.write( s2 )
IOError: [Errno 121] Remote I/O error

pi@switchdoclabs:~/SDL_Pi_SmartGardenSystem/SDL_Pi_HDC1000 $ sudo python testHDC1000.py
Test SDL_Pi_HDC1000 Version 1.1 - SwitchDoc Labs

Sample uses 0x40 and SwitchDoc HDC1000 Breakout board
Program Started at:2019-01-10 12:12:28

------------
Manfacturer ID=0x5449
Device ID=0x1050
Serial Number ID=0x936E80
configure register = 0x1000
turning Heater On
configure register = 0x3000
turning Heater Off
Traceback (most recent call last):
File "testHDC1000.py", line 41, in <module>
hdc1000.turnHeaterOff()
File "/home/pi/SDL_Pi_SmartGardenSystem/SDL_Pi_HDC1000/SDL_Pi_HDC1000.py", line 147, in turnHeaterOff
HDC1000_fw.write( s2 ) #sending config register bytes
IOError: [Errno 121] Remote I/O error

Last Edit: Jan 10, 2019 9:37:42 GMT -8 by robertr729

SDL Global Moderator Posts: 5,655 Raspberry Pi: Yes Other Device: PC, arduino, beagleBone	Smart Garden Errors when running testALLSensors.py Jan 10, 2019 9:52:19 GMT -8 Quote Select Post Deselect Post Link to Post Member Give Gift Back to Top Post by SDL on Jan 10, 2019 9:52:19 GMT -8 I would check your wiring very carefully on the HDC1080. Also run and post "sudo i2cdetect -y 1". BP

robertr729 New Member Posts: 4	Smart Garden Errors when running testALLSensors.py Jan 10, 2019 10:02:13 GMT -8 Quote Select Post Deselect Post Link to Post Member Give Gift Back to Top Post by robertr729 on Jan 10, 2019 10:02:13 GMT -8 It appears that when I disconnect the OLED that the test runs sucessfully. can there be an address conflict?

SDL
Global Moderator

Posts: 5,655
Raspberry Pi: Yes
Other Device: PC, arduino, beagleBone

Smart Garden Errors when running testALLSensors.py Jan 10, 2019 10:05:38 GMT -8

Quote

Post by SDL on Jan 10, 2019 10:05:38 GMT -8

Not unless there is a problem with one of the two I2C devices.

Put the OLED back in, run "sudo i2cdetect -y 1", post the results

Remove the OLED, run "sudo i2cdetect -y 1" and post the results.

BP

robertr729
New Member

Posts: 4

Smart Garden Errors when running testALLSensors.py Jan 10, 2019 10:30:58 GMT -8

Quote

Post by robertr729 on Jan 10, 2019 10:30:58 GMT -8

pi@switchdoclabs:~/SDL_Pi_SmartGardenSystem $ sudo i2cdetect -y 1
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: -- -- -- -- -- -- -- -- -- -- -- -- 3c -- -- --
40: 40 -- -- -- -- -- -- -- 48 -- -- -- -- -- -- --
50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: 60 -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --
pi@switchdoclabs:~/SDL_Pi_SmartGardenSystem $ sudo i2cdetect -y 1
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
40: 40 -- -- -- -- -- -- -- 48 -- -- -- -- -- -- --
50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: 60 -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --

robertr729 New Member Posts: 4	Smart Garden Errors when running testALLSensors.py Jan 10, 2019 10:48:27 GMT -8 robertr729 likes this Quote Select Post Deselect Post Link to Post Member Give Gift Back to Top Post by robertr729 on Jan 10, 2019 10:48:27 GMT -8 turned out to be a bad connector cable between the HDC1080 and the PiGrover board

SDL Global Moderator Posts: 5,655 Raspberry Pi: Yes Other Device: PC, arduino, beagleBone	Smart Garden Errors when running testALLSensors.py Jan 10, 2019 13:13:47 GMT -8 Quote Select Post Deselect Post Link to Post Member Give Gift Back to Top Post by SDL on Jan 10, 2019 13:13:47 GMT -8 Woohoo! That was the next thing I was going to have you check. Odd that taking the OLED out changed it, but in doing that you did physically disturb the system. BP

SwitchDoc Labs Product Support

Smart Garden Errors when running testALLSensors.py

Post by robertr729 on Jan 9, 2019 21:46:15 GMT -8

Post by SDL on Jan 10, 2019 9:52:19 GMT -8

Post by robertr729 on Jan 10, 2019 10:02:13 GMT -8

Post by SDL on Jan 10, 2019 10:05:38 GMT -8

Post by robertr729 on Jan 10, 2019 10:30:58 GMT -8

Post by robertr729 on Jan 10, 2019 10:48:27 GMT -8

Post by SDL on Jan 10, 2019 13:13:47 GMT -8

Quick Reply