Post by jorgeg73 on Apr 16, 2018 23:00:20 GMT -8
Hi to all have a question i am a backer for the kickstarter DIY Weather on your Raspberry Pi.
I have taken the dust of my weather kit, never used it until now. But i am unable to use it i have been reading i can connected to the pi and everything tuns on i also send the i send the ic2 test (sudo i2cdetect -y 1) i get information other than that i cant get anything only errors. i have been reading and theres a lot of mention of the I2C Bus Multiplexor, do i need it to start using the weather station?, i have also read that i need to connect some jumpers cable to give power to a board i am ok? I can not seem to see were they go.
Thanks and help
sudo i2cdetect -y 1
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: -- -- -- -- -- -- -- -- -- -- -- -- 3c -- -- --
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
50: -- -- -- -- -- -- -- 57 -- -- -- -- -- -- -- --
60: -- -- -- -- -- -- -- -- 68 -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- 77
sudo test python testSDL_Pi_TC
CA9545.py
Test SDL_Pi_TCA9545 Version 1.0 - SwitchDoc Labs
Sample uses 0x73
Program Started at:2018-04-16 23:53:02
Traceback (most recent call last):
File "testSDL_Pi_TCA9545.py", line 51, in <module>
tca9545 = SDL_Pi_TCA9545.SDL_Pi_TCA9545(addr=TCA9545_ADDRESS, bus_enable = TCA9545_CONFIG_BUS0)
File "/home/pi/SDL_Pi_GroveWeatherPi/SDL_Pi_TCA9545/SDL_Pi_TCA9545.py", line 47, in __init__
self._write(TCA9545_REG_CONFIG, config)
File "/home/pi/SDL_Pi_GroveWeatherPi/SDL_Pi_TCA9545/SDL_Pi_TCA9545.py", line 52, in _write
self._bus.write_byte_data(self._addr, register, data)
IOError: [Errno 121] Remote I/O error
pi@raspberrypi:~/SDL_Pi_GroveWeatherPi/SDL_Pi_TCA9545 $
I have taken the dust of my weather kit, never used it until now. But i am unable to use it i have been reading i can connected to the pi and everything tuns on i also send the i send the ic2 test (sudo i2cdetect -y 1) i get information other than that i cant get anything only errors. i have been reading and theres a lot of mention of the I2C Bus Multiplexor, do i need it to start using the weather station?, i have also read that i need to connect some jumpers cable to give power to a board i am ok? I can not seem to see were they go.
Thanks and help
sudo i2cdetect -y 1
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: -- -- -- -- -- -- -- -- -- -- -- -- 3c -- -- --
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
50: -- -- -- -- -- -- -- 57 -- -- -- -- -- -- -- --
60: -- -- -- -- -- -- -- -- 68 -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- 77
sudo test python testSDL_Pi_TC
CA9545.py
Test SDL_Pi_TCA9545 Version 1.0 - SwitchDoc Labs
Sample uses 0x73
Program Started at:2018-04-16 23:53:02
Traceback (most recent call last):
File "testSDL_Pi_TCA9545.py", line 51, in <module>
tca9545 = SDL_Pi_TCA9545.SDL_Pi_TCA9545(addr=TCA9545_ADDRESS, bus_enable = TCA9545_CONFIG_BUS0)
File "/home/pi/SDL_Pi_GroveWeatherPi/SDL_Pi_TCA9545/SDL_Pi_TCA9545.py", line 47, in __init__
self._write(TCA9545_REG_CONFIG, config)
File "/home/pi/SDL_Pi_GroveWeatherPi/SDL_Pi_TCA9545/SDL_Pi_TCA9545.py", line 52, in _write
self._bus.write_byte_data(self._addr, register, data)
IOError: [Errno 121] Remote I/O error
pi@raspberrypi:~/SDL_Pi_GroveWeatherPi/SDL_Pi_TCA9545 $