|
|
Post by hana on Aug 8, 2018 22:28:03 GMT -8
Hello.
I was buy the WeatherRack and Weather Board in last week.
For Running device, I found a open source in github page but I confuse what is the right source.
So I need to exactly the Open source path(name and address and process).
And do I need to other device?? such as converter?
Would you teach me a easy install guide?
your github source is very complex and has lots of products.
I hope to receive your help.
Thank you.
Please ask for a reply.
|
|
|
|
Post by hana on Aug 8, 2018 22:39:43 GMT -8
And what python version can I run?
|
|
|
|
Post by hana on Aug 9, 2018 1:59:24 GMT -8
one more question...
pi@raspberrypi:~/Downloads/SDL_Pi_WeatherBoard-master $ sudo python WeatherBoard.py
Traceback (most recent call last):
File "WeatherBoard.py", line 139, in <module>
weatherStation = SDL_Pi_WeatherRack.SDL_Pi_WeatherRack(anemometerPin, rainPin, 0,0, SDL_MODE_I2C_ADS1015)
File "./SDL_Pi_WeatherRack/SDL_Pi_WeatherRack.py", line 186, in __init__
self.ads1015 = ADS1x15(ic=ADS1015, address=0x48)
TypeError: 'module' object is not callable
how can I fix the error...?
I all follow the readme... I don't know....
|
|
|
|
Post by SDL on Aug 9, 2018 15:53:47 GMT -8
It looks like you don't have an ADS1015 or an ADS1115 ADC connected.
BP
|
|
|
|
Post by hana on Aug 21, 2018 20:13:06 GMT -8
Hello
After ADS1015 ADC connected, what should I install or process?
I installed ADC but continuously get the same error...
|
|
|
|
Post by hana on Aug 21, 2018 20:32:14 GMT -8
Hello After ADS1015 ADC connected, what should I install or process? I installed ADC but continuously get the same error... Traceback (most recent call last): File "WeatherBoard.py", line 139, in <module> weatherStation = SDL_Pi_WeatherRack.SDL_Pi_WeatherRack(anemometerPin, rainPin, 0,0, SDL_MODE_I2C_ADS1015) File "./SDL_Pi_WeatherRack/SDL_Pi_WeatherRack.py", line 186, in __init__ self.ads1015 = ADS1x15(ic=ADS1015, address=0x48) TypeError: 'module' object is not callable |
|
|
|
Post by hana on Aug 21, 2018 23:37:31 GMT -8
Maybe, Do I have to use J4, J5 (Grove Analog Wind Vane, Grove Digital Anemometer) ?
I want to use weatherRack sensor with weatherBoard and ADC.... Do I have additional material??
|
|
|
|
Post by SDL on Aug 22, 2018 6:36:07 GMT -8
You can interface the Weather Rack with the Weather Boar with J4 and J5.
On your Raspberry Pi, please post your results of "i2cdetect -y 1"
BP
|
|
|
|
Post by hana on Aug 22, 2018 17:59:27 GMT -8
Thank you.
I tried.
It is the results.
What that means?
And Are the J4 and J5 output module?
In my case, I plugged in RJ11 Plugs but additional do I need to connect J4, J5?
I confuse.
Thank you for your kind...
0 1 2 3 4 5 6 7 8 9 a b c d e f
00: -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
40: -- -- -- -- -- -- -- -- 48 -- -- -- -- -- -- --
50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- 77
|
|
|
|
Post by SDL on Aug 23, 2018 17:48:01 GMT -8
Pleas post a picture of your setup. It isn't clear what you are asking me.
BP
|
|
|
|
Post by hana on Aug 28, 2018 0:37:36 GMT -8
Sorry; Thank you reply.
May I ask you question?
'The output of the Wind Vane should be connected to a 10K pullup resistor'
This sentence is that I should connect 10k pullup resistor, but Weather Board and Weather Rack sensor connector are grove and plug...
so if I want to connect pullup resistor, Do I have to cut the plug and grove and then need to add pullup resistor by connecting the wires to a bread board?
The current state is that everything is connected and the source code is running, but sensor data is not output. I want to solve the problem...
Thank you, sir
|
|
|
|
Post by SDL on Aug 28, 2018 13:39:24 GMT -8
The WeatherBoard includes the 10K Pullup resistor.
Check your wiring! That is likely the problem.
BP
|
|
