|
|
New SGS
May 5, 2019 14:41:51 GMT -8
Post by pamisano on May 5, 2019 14:41:51 GMT -8
I recently completed the SGS project and, aside for the oled display being on the fritz, SwitchDoc is graciously sending me a new one, the system appears to work. I ssh'd into the Pi, started the system, had the moisture sensor in a dry plant and the pump kicked on for about one maybe two seconds, shut off and in my terminal window, I see:
activeAlarm= False
lastAlarm= True
activeAlarm= False
lastAlarm= True
activeAlarm= False
lastAlarm= True
Over and over. Any idea what that means?
Also, is there any troubleshooting documentation or documentation that discusses the output either to the terminal or the oled?
Thanks,
Pete
|
|
|
|
New SGS
May 6, 2019 15:37:28 GMT -8
Post by SDL on May 6, 2019 15:37:28 GMT -8
Pamisano,
Please post the entire listing if possible from startup until you see this. We are trying to figure out what is going on. Also publish your configuration file (confocal.py) with any passwords removed.
BP
|
|
|
|
New SGS
May 11, 2019 6:09:42 GMT -8
Post by pamisano on May 11, 2019 6:09:42 GMT -8
pi@raspberrypi:~/SDL_Pi_SmartGardenSystem $ sudo python SGS.py
[Errno 121] Remote I/O error
[Errno 121] Remote I/O error
Error accessing 0x49: Check your I2C address
Error accessing 0x49: Check your I2C address
Error accessing 0x4A: Check your I2C address
Error accessing 0x4A: Check your I2C address
SGS Version 009 - SwitchDoc Labs
Program Started at:2019-05-11 09:05:53
ADS1115: Present
OLED: Present
Sunlight Sensor: Present
hdc1000 Sensor: Present
Ultrasonic Level Sensor: Present
----------------------
Plant / Sensor Counts
----------------------
Sensor Count: 1
Pump Count: 1
----------------------
Extender Devices
----------------------
ADS1115_Ext1: Not Present
ADS1115_Ext2: Not Present
GPIO Extender 1: Not Present
GPIO Extender 2: Not Present
----------------------
Future Smart Garden System Expansions
----------------------
SunAirPlus: Not Present
Lightning Mode: Not Present
Solar Power Mode: Not Present
MySQL Logging Mode: Not Present
----------------------
Moisture Sensor: Present
----------------------
-----------------
Scheduled Jobs
-----------------
Jobstore default:
blinkLED (trigger: interval[0:00:05], next run at: 2019-05-11 09:05:59 CDT)
forceWaterPlantCheck (trigger: interval[0:00:08], next run at: 2019-05-11 09:06:02 CDT)
updateState (trigger: interval[0:00:10], next run at: 2019-05-11 09:06:04 CDT)
statusLEDs (trigger: interval[0:00:15], next run at: 2019-05-11 09:06:09 CDT)
checkForAlarms (trigger: interval[0:00:15], next run at: 2019-05-11 09:06:09 CDT)
tick (trigger: interval[0:01:00], next run at: 2019-05-11 09:06:54 CDT)
checkAndWater (trigger: interval[0:15:00], next run at: 2019-05-11 09:20:54 CDT)
-----------------
lastAlarm= True
activeAlarm= False
lastAlarm= True
activeAlarm= False
lastAlarm= True
activeAlarm= False
lastAlarm= True
activeAlarm= False
Tick! The time is: 2019-05-11 09:06:54.901572
lastAlarm= True
activeAlarm= False
|
|
|
|
New SGS
May 11, 2019 6:54:19 GMT -8
Post by pamisano on May 11, 2019 6:54:19 GMT -8
Also re-ran the all sensor test, the moisture test and tank calibration. All provided results as expected, but keep getting the lastAlarm/ActiveAlarm upon execution of SGS.py
|
|
|
|
New SGS
May 12, 2019 6:54:31 GMT -8
Post by SDL on May 12, 2019 6:54:31 GMT -8
OK. Turns out that this is just debugging information. Comment out line 906 and line 907 in SGS.py so they look like this.
#print "lastAlarm=", lastAlarm
#print "activeAlarm=", activeAlarm
BP
|
|
|
|
New SGS
May 13, 2019 7:04:30 GMT -8
SDL likes this
Post by pamisano on May 13, 2019 7:04:30 GMT -8
rgr, will do. Thanks!
|
|
