david
Junior Member
Posts: 95
Raspberry Pi: Yes
|
Post by david on Jul 15, 2019 4:30:16 GMT -8
Ok, I did restart Blynk at 0722 today.
|
|
david
Junior Member
Posts: 95
Raspberry Pi: Yes
|
Post by david on Jul 16, 2019 4:25:38 GMT -8
Well, looks like you are correct. I appears to be related to Blynk. It crashed/rebooted twice yesterday. Attachments:LogB.txt (18.7 KB)
LogA.txt (3.39 KB)
|
|
|
Post by SDL on Jul 16, 2019 8:06:14 GMT -8
David,
Great information. Now, our units perform flawlessly with Blynk.
I'm issuing an RMA for the WeatherPlus board. That is the culprit I believe.
Please PM us your shipping address and we will ship you a new one.
When you get it, please sends us yours for testing.
SwitchDoc Labs RMA# 071619-01 909 S Shelley Lake Lane Spokane Valley, WA 99037
BP
|
|
|
Post by Ruben on Jul 16, 2019 13:55:22 GMT -8
I have the same issue. The application is working fine when offline and initially when I set up the WiFi, however once we capture the Blink Auth Token it start rebooting in a loop: it reboots, set up wifi, display sensor readings, display time,... then reboots again. Blink detects that that the board is online every time it reboots, but never loads sensor readings. In the Blink status tab it show the entries in the log but it never reports Last Sample.
|
|
|
Post by SDL on Jul 16, 2019 18:41:03 GMT -8
Ruben,
Hold on and let's see if a new board fixes Davids problem.
BP
|
|
david
Junior Member
Posts: 95
Raspberry Pi: Yes
|
Post by david on Jul 21, 2019 3:35:21 GMT -8
Hi. I got the replacement. Set it up and ran ok overnight. Then input Blynk key and started a reboot cycle (maybe like what Ruben is describing, very odd coincidence). Log attached. Also just now looking at log I see NAN on AM2315 just before I input Blynk. And just to be sure, please give me address to ship first board to. Thanks David Attachments:blynkredact.txt (141.58 KB)
|
|
|
Post by SDL on Jul 21, 2019 11:40:19 GMT -8
David,
SwitchDoc Labs RMA# 071619-01 909 S Shelley Lake Lane Spokane Valley, WA 99037
This now sounds like Blynk has changed something. This now looks like a software problem. We will start looking into it. I know Blynk has released a new library. I'll recompile with the new library and issue a new version.
BP
|
|
david
Junior Member
Posts: 95
Raspberry Pi: Yes
|
Post by david on Jul 22, 2019 5:25:52 GMT -8
Hi BP New info on the new Blynk issue. It may be the software on the board as sent out and not the version on GitHub. Just to check, I uploaded software that I have modified from the SwitchDoc repository and it appears to connect to and run Blynk just fine. Has been less than 30 minutes, but looking good. David
|
|
|
Post by Ruben on Jul 22, 2019 7:26:15 GMT -8
Here is my Log,... as you said it seems is a problem with the Blynk version compiled. Please let us know when a new version is released to test it....
OurWeather ESP8266-12 -------------------- Version: 035 Compiled at:12:12:06 Feb 22 2019 Free Sketch Space on OurWeather:3682304 SunAirPlus Not Present WXLink Not Present port number = 80 AirQuality Extension Not Present OurWeather IP Address:192.168.1.95 OurWeather Gateway Address:192.168.1.254 OurWeather subnet Mask:255.255.255.0 displayMode=1 displayMode=18 No BMP180 detected No BMP280 detected AM2315 Detected... PubNub set up [16605] ___ __ __ / _ )/ /_ _____ / /__ / _ / / // / _ \/ '_/ /____/_/\_, /_//_/_/\_\ /___/ v0.5.4 on ESP-12
[16610] Connecting to blynk-cloud.com:80 [16793] Ready (ping: 85ms). 5 second Loop executed Free heap on ESP8266:30088 --------------- DS3231 Clock --------------- 2019-07-16 17:13:02 --------------- AM2315 --------------- Temp: 19.10 Hum: 60.70 DwPt: 11.24 --------------- No BMP180/BMP280 Found --------------- --------------- SunAirPlus Not Present --------------- --------------- WXLink Not Present --------------- --------------- WeatherRack --------------- windSpeedMin =0.00 windSpeedMax =0.00 windGustMin =0.00 windGustMax =0.00 windDirectionMin =180.00 windDirectionMax =180.00 currentWindSpeed=0.00 currentWindGust=0.00 Wind Direction=180.00 Cumulative Rain = 0.00 displayMode=4 OutOfDisplay [40012] Heartbeat timeout [40015] Connecting to blynk-cloud.com:80
Exception (9): epc1=0x4010499a epc2=0x00000000 epc3=0x00000000 excvaddr=0x00000049 depc=0x00000000
>>>stack>>>
|
|
|
Post by SDL on Jul 23, 2019 6:34:44 GMT -8
Will do! Mid August I would say.
BP
|
|
david
Junior Member
Posts: 95
Raspberry Pi: Yes
|
Post by david on Jul 24, 2019 17:33:19 GMT -8
BP I am not sure that the new board is any better than the one I sent back to you. I had an unexpected Blynk related crash/reboot Monday evening and then again this evening. It ran just over 2 days between reboots. Logs attached. David
|
|
|
Post by SDL on Jul 25, 2019 20:01:37 GMT -8
Thank you for the log information. Pretty conclusive that the problem is with handling a Blank error. Not necessarily Blynk itself, but rather the response to a Blynk connection error.
We are adding it to our bug list.
BP
|
|